Our Top Picks Guides Categories Gear & Peripherals Laptops PC Components Company How We Review About Us Contact
Our recommendations are made independently. As an Amazon Associate we earn from qualifying purchases. Learn more ›
CPU Coolers and Fans

7 Best Thermal Paste for CPU and GPU Repasting (2026)

A dried-out paste layer can push a CPU into thermal throttling long before the cooler itself is the problem. See how these picks compare on consistency, spread method, and how many applications you get per tube.

Published Nov 19, 2026 4 min read

You pull the side panel to swap a cooler, and the old paste has baked into a chalky crust that flakes off in the socket. Or you finish a build, boot up, and the fans ramp hard within minutes because the contact patch between the heat spreader and the cold plate is uneven. Thermal paste is the cheapest part in the box and the easiest one to get wrong.

The differences between tubes come down to consistency, how the paste spreads under mounting pressure, whether the formula stays put through repeated heat cycles, and how much you get for a single application. I went through the listings for the Best Thermal Paste, comparing stated viscosity, filler type, included applicators, and the surfaces each brand says the paste suits.

My overall pick for best thermal paste is the Corsair XTM70 Extreme Performance Thermal Paste. It ships with an applicator kit and cleaning wipes, so a first-time repaste does not turn into a hunt for a plastic spreader and rubbing alcohol. My top picks are just below.

Best Thermal Paste at a Glance

A Note on Ratings. Manufacturer specs are not always independently verified, and real-world results vary with the rest of your system, drivers, and settings. We compare every pick on published specs, warranty terms, and verified owner feedback before it makes this list. Always follow the manufacturer's installation and safety instructions.

In-Depth Reviews

Corsair XTM70 Thermal Paste 3g with Cleaning Wipes
9.9 PGH Score
Excellent

Corsair XTM70 is a 3g thermal paste rated for processors up to 250W TDP, with low viscosity and three cleaning wipes included.

Key Spec
Rated for processors up to 250W TDP
Size
3 grams
Included
Three cleaning wipes and applicator kit
Compatibility
Intel and AMD processors

Pros

  • +Rated for processors up to 250W TDP
  • +Low viscosity for even, clean spreading
  • +Three cleaning wipes included for old paste
  • +3g tube allows multiple applications

Cons

  • −3g tube runs out faster on repeated rebuilds
  • −Paste application needs care to avoid air pockets

Detailed Review

Corsair XTM70 is a 3g thermal paste rated for processors up to 250W TDP and higher, which puts it in the range of high-end desktop CPUs and graphics cards rather than low-power office builds. The low viscosity is the detail that matters most here, since a thinner paste spreads more evenly across the cold plate with the included applicator kit. Three cleaning wipes also ship in the box, so removing old paste before a fresh application does not require a separate purchase.

For my money, this suits a builder swapping a cooler or repasting a GPU who wants one tube to cover several jobs. The 3g size is enough for multiple applications, though a single tube will not last through a long run of rebuilds. Applicator kit included makes controlled spreading easier than a bare syringe.

Paste application still demands care, since uneven pressure or trapped air can undercut contact between the processor and cold plate. I would keep this on the bench for high-TDP desktop work rather than thin-and-light laptops.

2 Best for First Repaste

Corsair TM30 Thermal Paste with 3g Applicator

Corsair
Corsair TM30 Thermal Paste with 3g Applicator
9.8 PGH Score
Excellent

Corsair TM30 is a zinc oxide thermal compound in a 3g tube with an applicator and stencil for CPU and GPU use.

Key Spec
3 grams zinc oxide thermal compound
Included
Applicator stencil and spreader
Compatibility
CPU and GPU heat spreaders
Size
0.51 x 0.98 x 4.53 inches

Pros

  • +Applicator and stencil reduce guesswork during mounting
  • +Low-viscosity compound spreads easily across IHS
  • +Non-conductive formula avoids shorting nearby pins
  • +3g capacity allows several CPU or GPU applications

Cons

  • −Zinc oxide base trails higher-end compounds in thermal conductivity
  • −No stated cure time or long-term performance data
  • −Small 3g tube may run short on multiple large GPU dies

Detailed Review

Corsair TM30 is built around a zinc oxide compound and a 3g tube, with an applicator stencil and spreader included. I see that stencil as the practical part for anyone replacing paste on a CPU or GPU, since it removes the guesswork about how much to apply. The low-viscosity formula is meant to fill microscopic abrasions and channels on the heat spreader.

The non-conductive claim matters for builders working near exposed pins or small surface-mount components. I would keep this in mind for a first paste swap, where a stray blob is less likely to cause a short. The tube size suits a single CPU or one GPU die, but a large GPU with a wide cold plate may use most of it.

For my money, this is a straightforward pick for a basic repaste on an older laptop or desktop. I would not expect it to match a higher-end compound, and the data does not state a cure time or long-term consistency figure.

ARCTIC MX-4 Thermal Paste 4g with Spatula
9.8 PGH Score
Excellent

ARCTIC MX-4 is a 4g carbon-based thermal paste that is metal-free and non-electrically conductive, supplied with an application spatula.

Key Spec
Carbon microparticle formula
Included
4g syringe and spatula
Safety
Metal-free, non-electrically conductive
Size
1.2 x 2.8 x 5.9 inches

Pros

  • +Non-conductive formula reduces short-circuit risk
  • +Carbon microparticles for high thermal conductivity
  • +Included spatula simplifies application for beginners
  • +Authenticity check verifies genuine product

Cons

  • −Only 4g supplied, limiting to a few applications
  • −No included cleaning wipes for surface prep

Detailed Review

ARCTIC MX-4 uses carbon microparticles to achieve high thermal conductivity, and its metal-free, non-electrically conductive formula removes short-circuit risk on CPU and GPU surfaces. The 4g syringe includes a spatula, which helps beginners spread an even layer without guesswork. I value the authenticity check for verifying a genuine tube, since counterfeit paste is a real problem in this category. The main trade-off is the small 4g quantity, which limits how many repastes you can do. For a single CPU or GPU refresh, that amount is sufficient, but for multiple builds you will need a larger tube. I see this as a solid choice for first-time repastes or a single-card cleanup.

4 Best for Single Repaste

Thermal Grizzly Kryonaut 1g Thermal Paste

Thermal Grizzly
Thermal Grizzly Kryonaut 1g Thermal Paste with Cleaning Wipes
9.8 PGH Score
Excellent

Thermal Grizzly Kryonaut is a 1 gram thermal paste for CPUs and GPUs, bundled with 12 wet and dry cleaning wipes.

Key Spec
1 gram syringe
Included
6 wet and 6 dry cleaning wipes, spatula
Stated Temperature
Does not dry out at 80°C
Size
3.94 x 0.79 x 0.79 inches

Pros

  • +Includes spatula for controlled paste spreading
  • +Wet and dry wipes simplify surface prep
  • +Stated to stay stable at 80°C
  • +One gram suits a single CPU or GPU job

Cons

  • −One gram leaves little margin for multiple applications
  • −No stated thermal conductivity figure to compare

Detailed Review

Thermal Grizzly Kryonaut ships as a 1 gram syringe with a spatula and a dozen cleaning wipes, six wet and six dry. That bundle matters because repasting a CPU or GPU means removing old paste first, and the wipes save a separate purchase. The spatula also lets you spread a thin, even layer instead of relying on a pea-sized dot alone.

The features state Kryonaut does not dry out even at 80°C, which is the temperature range a hot GPU or overclocked CPU can sit in. For a build where the cooler gets removed and reseated, that stability is the practical draw. I would choose this for a single CPU or GPU repaste where surface prep matters as much as the paste itself.

The catch is the 1 gram tube. That is enough for one application on a processor or graphics card, but not a spare tube for a second build or a friend's machine. No thermal conductivity number is given, so I cannot rank it against other pastes by spec alone.

5 Best for Cooler Mounts

ARCTIC MX-7 8g Thermal Paste with High-Viscosity

ARCTIC
ARCTIC MX-7 8g Thermal Paste with High-Viscosity Formula
9.7 PGH Score
Excellent

ARCTIC MX-7 is an 8 g thermal paste with a dense, high-viscosity formula and high filler content for heat transfer.

Weight
8 g
Consistency
Dense, high-viscosity
Electrical
Non-conductive and non-capacitive
Application
Spreads under cooler pressure, not by hand

Pros

  • +High filler content supports strong heat transfer
  • +Non-conductive formula safe on exposed CPU and GPU dies
  • +Dense consistency resists pump-out across thermal cycles
  • +Low adhesion spreads evenly under cooler pressure

Cons

  • −Cannot be spread manually by design
  • −Requires careful cooler mounting for even coverage

Detailed Review

The MX-7's defining trait is its dense, highly viscous consistency, which ARCTIC says cannot be spread manually. Instead, its low adhesion lets the paste distribute under cooler pressure into a thin bond line without trapped air.

That approach suits CPU and GPU remounts where even mounting pressure is achievable, and the high filler content is what ARCTIC points to for heat transfer. The electrically non-conductive formula also keeps it safe on exposed dies.

My reservation is the application method itself, since anyone used to spreading paste by hand will need a different routine. For a straightforward cooler mount, the 8 g tube gives enough for several reapplications.

6 Best for First Builds

BSFF Thermal Paste 1.8g with Toolkit for CPU

BSFF
BSFF Thermal Paste 1.8g with Toolkit for CPU and GPU
9.6 PGH Score
Very good

BSFF 1.8g carbon-microparticle thermal paste, non-conductive and metal-free, with a toolkit for CPU, GPU, and heatsink applications.

Size
1.8g
Type
Carbon microparticle, non-conductive
Included
Toolkit
Stated Lifespan
At least 5 years

Pros

  • +Non-conductive formula adds safety margin on exposed dies
  • +Carbon microparticle compound targets efficient heat transfer
  • +1.8g tube handles several repaste jobs
  • +Toolkit included for cleaner application

Cons

  • −No rated thermal conductivity figure to compare against alternatives
  • −Five-year durability claim lacks independent verification

Detailed Review

BSFF's 1.8g thermal paste leans on a metal-free, non-conductive carbon microparticle formula, which matters most when you are repasting a laptop CPU or a GPU die where a stray smear could bridge contacts. The included toolkit is the practical part for first-time builders, since spreading paste evenly is where most beginner jobs go wrong. I would keep this on hand for a budget build or a quick cooler swap rather than a flagship overclocking project.

The 1.8g syringe covers several applications, so one tube can handle a CPU and a GPU before running dry. What the data does not give is a rated thermal conductivity or a measured temperature drop, so treat the performance claims as the brand's wording rather than a verified figure. The stated five-year lifespan is likewise a manufacturer claim, not something I can confirm from the spec sheet.

For a student building a first PC or a remote worker refreshing an older desktop, the safety of a non-conductive paste and the bundled spreader make this a sensible pick. Enthusiasts chasing the lowest possible temperatures will want a paste with published conductivity numbers instead.

7 Best for GPU Repaste

ARCTIC MX-6 Thermal Paste with 4g Non-Conductive

ARCTIC
ARCTIC MX-6 Thermal Paste with 4g Non-Conductive Formula
9.5 PGH Score
Very good

ARCTIC MX-6 is a 4g non-conductive thermal paste with improved composition for lower thermal resistance than MX-4.

Size
4 grams
Color
Grey
Conductivity
Non-conductive and non-capacitive
Stated Performance
Lower thermal resistance than MX-4

Pros

  • +Non-conductive and non-capacitive for risk-free application
  • +Lower thermal resistance than MX-4 per ARCTIC's stated comparison
  • +Viscosity works for direct-die GPU and console repaste jobs
  • +Authenticity check confirms genuine ARCTIC product

Cons

  • −4g tube runs out quickly across multiple full repaste jobs
  • −No included applicator or spreader tool for even coverage

Detailed Review

ARCTIC's MX-6 is a 4g grey paste built around a non-conductive, non-capacitive formula, which matters if you are repasting a CPU or a graphics card and want to avoid any risk of bridging contacts. The composition is stated to have measurably lower thermal resistance than the older MX-4, so it is the more current pick from ARCTIC's own lineup.

The viscosity is the detail I would weigh most for GPU work. ARCTIC says it suits direct-die cooling on graphics cards and console processors, where a thicker paste stays put under the cooler rather than pumping out. For a laptop or desktop CPU repaste, the same consistency spreads fine under mounting pressure.

The catch is quantity. A 4g tube covers a repaste or two, and no spreader tool is included, so plan your application method before you open it. I would reach for this if you are refreshing a GPU or console and want a non-conductive paste with a stated improvement over MX-4.

FAQs

How often should thermal paste be replaced?

Replacing paste every few years, or whenever you lift the cooler off the CPU, is the usual practice. Paste that has dried and cracked loses contact area, which shows up as higher temperatures under sustained load in games or renders. If temperatures climb without a change in ambient room heat, a repaste is a reasonable first step.

Does the spread method change the result?

A small center dot or thin line usually covers a desktop CPU once the cooler clamps down. Some formulas, like the ARCTIC MX-7, are designed to spread only under mounting pressure, so read the listing before you reach for a spatula. Too much paste can squeeze out over the socket edge, so keep the layer thin.

Is non-conductive paste safer for a first build?

Non-conductive paste removes the short-circuit risk that liquid metal carries if it drips onto pins or traces. Most pastes here are listed as metal-free and non-electrical conductive, which suits beginners and anyone working near exposed components. Liquid metal still has its place for delidded chips, but it demands far more care.

How much paste does one tube cover?

A single desktop CPU application uses a pea-sized amount, so even a small tube covers several repastes. Larger tubes make sense if you also service a GPU, a console, or a laptop. Check the listing for the stated weight and whether an applicator or cleaning wipes are included before you decide.

Final Thoughts

What matters most is a paste that spreads evenly, stays stable through heat cycles, and comes with the tools to apply it cleanly. The Corsair XTM70 Extreme Performance Thermal Paste is my pick for a high-end desktop build, where the included applicator kit and wipes make a clean repaste straightforward and the listing rates it for high-TDP processors. If you want to spend less, the Corsair TM30 Performance Thermal Paste covers a basic CPU or GPU repaste with an included stencil and spreader.

Skip the premium tubes if you are servicing a stock cooler on a low-power chip and just need a thin, reliable layer. Anyone pairing a new cooler with a fresh paste job should also confirm the cooler’s mounting hardware and clearance, and a look at CPU coolers and fans helps match the paste to the cold plate. Check the current price on Amazon, and the right tube removes the guesswork about whether your contact patch is the weak link.

Contents
  1. Best Thermal Paste at a Glance
  2. In-Depth Reviews
  3. FAQs
  4. Final Thoughts